How To Paint A Fiberglass Exterior Door

Tin can Fiberglass Front Doors Be Painted?

Fiberglass forepart doors are very popular considering they are bonny and durable. They can be textured or polish, merely the ones that are textured to look and feel like wood are well-nigh mutual. The doors come in colors or finished like wood. When a fiberglass door starts to look worn, chipped, and scratched, it can be painted to look new again.

Preparing the Door for Painting

Though it is easier to become good coverage when the door is removed and laid flat, it is often difficult to rehang the door. Information technology is less complicated to carefully pigment the door while it is in identify. Painting a door while in place also makes information technology easier to proceed a home secure during the painting process.

The success of a fiberglass door painting job depends on correctly preparing the door earlier painting starts. When a door is beingness painted in place, steps should be taken to protect the door frame and the floor beneath the door. Laying out a painter'southward tarp and taping off the area around the door that will not be painted is a expert start.

The door should be well-cleaned with soap and water, rinsed, then cleaned with a rag dipped in a cleaner such as mineral spirits or acetone. Some experts reverse the gild of cleaners used. When the door is clean, it should be left to dry and for the odour from the cleaning chemicals to go away. There should be adequate ventilation during this process.

If there is woods trim around drinking glass inserts, carefully sand information technology with 220-dust sandpaper being conscientious not to sand the fiberglass surface of the door. Wipe the door with a soft cloth dipped in acetone or a tack rag to become rid of any dust.

Carefully record over glass inserts, hinges, and the doorknob without getting tape on surfaces to be painted.

Now, open the bonding primer, stir, and with a minor brush apply a generous glaze to the wood trim but. Dry this surface area thoroughly earlier proceeding.

Choosing and Applying the Pigment

Now it is time to apply the master coat of paint. The type of pigment used to paint a door is important. A door needs a very durable type of paint. The paint used for an outside door should be classed as an exterior pigment. These paints must also be rated for painting over fiberglass and come in gloss, semi gloss, or flat finishes. The best fiberglass paints are 100% acrylic, polyester, polyurethane, or epoxy.

If primer is being used offset, keep with the same base material and manufacturer. Fiberglass doors come in different resins and finishes. This affects the paint option. If the fiberglass is an epoxy resin, the pigment choice should be an epoxy-based i. If the fiberglass is a polyester-resin, the paint called should be polyester-based.

Oil-based and lacquer paints are not recommended for painting fiberglass doors. The correct type of paint will offer the best protection for a door. In that location volition exist a better bond when the right blazon of pigment is used. Things like peeling, bubbles, or flaking volition be avoided.

Painting the Door

The outset stride in applying paint is to open up the can and slowly stir the pigment. Continue stirring slowly until the pigment is evenly mixed. Stirring too fast may cause bubbles to form.
First the pigment awarding process by dipping a small castor in the paint, and so wiping off the backlog on the edge of the can. Now, pigment the wooden trim around the drinking glass inserts.
Use a larger paintbrush to pigment the recessed door panels following the direction of the grain. Use fifty-fifty, smooth stokes and smooth out as you go to avoid runs and drips.
Next, paint the stile, or vertical centerboard, of the door. This element requires an fifty-fifty upwards and down stroke of the paintbrush.
Now, it is time to paint the horizontal rails of the door. Beginning at the top of the door and work down. Yous volition be using a side to side stroke to gently alloy into previously painted areas.
The remaining vertical stiles are painted next. This requires up and downwards paintbrush strokes and gentle blending at previously painted areas. Work from left to right and cease with the door edges.
This main coat of paint needs to dry overnight. Then a person can choose to employ a 2d coat of paint or a sealant coat. This new coat of finish will need to dry thoroughly before the tape is removed and the door is set up to use again.

Practise not hesitate to buy fiberglass doors or to repaint an existing fiberglass door. The results will be worth the endeavor.